Lenkräder, Lenksäulen und Lenkgetriebe sowie Teile davon, für Zugmaschinen, Omnibusse, Personenkraftwagen, Lastkraftwagen und Kraftfahrzeuge zu besonderen Zwecken, a.n.g.

8708 94 20 00

For the industrial assembly of: Vehicles of heading|8703; Vehicles of heading|8704|with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2|500|cm$3|or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2|800|cm$3; Vehicles of heading|8705

8708 94 35 00

Steering wheels, steering columns and steering boxes

8708 94 91 00

Of closed-die forged steel

8708 94 99 10

Hub gear made of cold rolled carbon steel (per ASTM A1008), molded into the plastic and pressed on pinion, with: -an outer diameter of 81,2 mm or more, but not more than 82,55 mm, -an inner diameter of 25,9 mm or more, but not more than 25,97 mm, -a height of the lower side of inner diameter of 11,63 mm or more, but not more than 12,13 mm, -a height of the upper side of inner diameter of 3,25 mm or more, but not more than 3,5 mm, -an overall height of 11,63 mm or more, but not more than 19,5 mm for use in the manufacture of vehicle's steering system

8708 94 99 20

Intermediate steering shaft forming part of the steering column with: -a torsional rigidity of 25 Nm/degree or more, -a tubular male shaft in welded carbon steel tube (per GB/T 699 grade 20), -a tubular female shaft in welded carbon steel tube (per with GB/T 699 grade 20), -two spiders universal joint made of chromium alloy steel (per GB/T 5216 grade 20CrMnTiH), -a length in nominal telescope position of 396 mm or more but not more than 467 mm, -a coupling interface on both ends with internal toothing, -two cardan joints on both sides, -a telescope shaft function with a range of 74 mm or more but not more than 115 mm, for use in the manufacture of vehicle's steering system

8708 94 99 30

Lower assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45 or JIS G4051 grade S45C) with: -an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 66,39 mm or more but not more than 88,64 mm, -an outer diameter of 27,47 mm or more but not more than 28,38 mm, -an inner hole of diameter 6,50 mm or more but not more than 6,58 mm, -an external 26-teeth spline with major diameter 21,18 mm or more but not more than 21,44 mm, -a knurling on a part of outer surface of major diameter 26,0 mm or more but not more than 26,1 mm, -with or without an external 24-tooth spline and with a major diameter 24,75 mm or more but not more than 25 mm, for use in the manufacture of vehicle's steering system

8708 94 99 40

Upper assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45) with: -an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 165,3 mm or more but not more than 204,2 mm, -an outer diameter of 22,87 mm or more but not more than 22,92 mm, -an internal hole of diameter 6,50 or more but not more than 6,58 mm, -an external spline, for use in the manufacture of vehicle's steering system

8708 94 99 50

Lower shaft as part of the steering column made of aluminium alloy (per ASTM B221M grade 6105), air quenched and tempered with: -an ultimate torsional strength of 260 Nm or more, -a length of 296,7 mm or more but not more than 297,8 mm, -an external 18-tooth spline on all shaft length with major diameter of 28,7 mm or more but not more than 29 mm, -an 18-tooth internal spline with a minor diameter of 19,7 mm or more but not more than 20 mm, for use in the manufacture of vehicle's steering system